•  
• 

Features

Improved Accel/Decel Time - Max. 3 times Faster

himac original technology "PWM motor control"

• PWM (pulse width modulation) motor control has realized substantial reduction in acceleration and deceleration time.
• Acceleration and deceleration time of CR-G‡V Series with large capacity rotor has improved max. 3 times faster than the one of our former models of high-speed refrigerated centrifuge.
• Reducing running time contributes to energy saving and reducing CO₂
  
  
  

Energy Saving

Acceleration and Running at set speed

• Reduced electricity consumption substantially by IGBT inverter

Deceleration

• himac regenerative braking system re-generates max.40% electricity used for acceleration and running.
• It reduces heat radiation into the room and is high efficient for energy saving.
  Former models : Kinetic Energy Heat radiation into the room
  New System : Kinetic Energy Regenerated to electricity and reused

Self-Locking Rotor System

• • Hitachi Koki is a pioneer to introduce "Self-Locking Rotor System" in Centrifuges.
  • Just placing a rotor onto the drive shaft
  • No need to fix the rotor by screw or push the button to lock or unlock the rotor.
  • Automatic rotor identification (PAT.)
  • Optimized running condition is automatically adjusted.
    (such as compensating for air friction and implement temperature control)
• 

Advanced Technology

Non-Contact Imbalance Protection (PAT.)

• Continuous measurement of oscillation over the entire rpm range
• The system immediately detects abnormal vibrations and stops rotation.

Actual Control of Net Run-Time(PAT.)

• The timer starts when the set speed is attained by himac original actual run timer function.
• Enables to obtain high-reproducibility separation.

Pre-cooling Chamber (PAT.)

• Maintaining temperature inside chamber room at low temperature with preventing from icing, in order to reach target temperature shortly

Specifications

Specifications

Model	CR22GⅢ	CR21GⅢ
Maximum speed (rpm)	22,000	21,000
Maximum RCF (x g)	55,200	50,300
Maximum capacity (ml x pcs)	1,000 x 4
Drive motor	High-torque brushless high-frequency motor
Temp. Control Range	-20 to +40 degree C
Accel/Decel Mode	Accel : 9 modes / Decel : 9 modes, free deceleration
Refrigerator	1.5kW (Coolant :R404a)
Power requirements	Single phase, AC 220/230/240V±10%, 30A, 50/60Hz
Dimensions (wxDxHmm)	752 x 810 (w/o rear duct) x 1,144 (panel opened) (hight to to table: 858)
Weight (kg)	300

Notes:
• * The start and end of revolution can be controlled by inputting their time and date. This is the same function as the RTC of the CP-WX/CP-MX/CS-GXL Series ultracentrifuge.
• The CR-GⅢ Series centrifuges must be operated with the automatically identifiable rotors in order to confirm to the CE marking requirments. The following rotors are not equipped with the automatically identification function.
  When using the rotors below, please place an order the CR-GⅢ Series centrifuges without CE mark.
  Rotors to be used with CR-GⅢ Series without CE marking.
  Rotor Models : R17A, R16AF, R12A, R12A2, R11D, R10A, R6S , R18C , R13C and R10C.
  Due to time elapsed, we highly recommend to retire following rotors if you still use ;
  Rotor Models : RPR20-2, RPR20-3, RPR20-4, RPR18-3, RPR16, RPR12-2, RPR10-2, RPPR9-2.
  
  For further information, please kindly contact us via "Contact Us" of this web site.

Cautions during installation:
• To optimize the heat exchange efficiency of the refrigerator unit, install in a space according to the specifications.
• Install on a stable floor.
• Avoid installation near equipment that could be a heat source, or in direct sunlight.
• An extension cord should not be used.
• The heat radiation rate of the centrifuge is about 2.3 kw (about 2,000 kcal/h).
• As a safety precaution, ground the equipment properly according to applicable electrical codes.

• page top